Veris Verabar V500_V510 Installation Instructions Manuel d'utilisateur télécharger pdf

Verabar V500 and V510

INSTALLATION INSTRUCTIONS

1.0 SCOPE

These instructions provide procedures for installing the

V500 and V510 Verabar flow sensor. Procedures are

given for all industrial flow measurement applications

including liquid, steam and gas service for both horizontal

and vertical piping configurations.

2.0 RECEIVING INSPECTION

The following tasks should be performed as part of the

receiving inspection procedure:

• Check items received against the packing list.

• Check sensor nameplate for proper model number,

serial number and customer number.

• Verify that the actual pipe diameter matches the ID

stated on the sensor nameplate.

• Check the bullet shaped sensor tube for any signs

of damage. Damage to the sensor tube may result

in erroneous flow readings.

• Check the round cover tube for any damage,

especially axial gouges or scratches. Damage to

the cover tube may prevent the ferrule from sealing

properly.

3.0 SAFETY PRECAUTIONS

The following tasks should be conducted prior to install-

ing the Verabar flow sensor:

• Check maximum operating conditions on the flow

sensor nameplate and verify that they exceed the

maximum conditions of the installation. If any

pressure, temperature or flow limits will be

exceeded, consult the factory before proceeding.

• Check that the pipe is depressurized and drained

prior to installation.

• Check that all pressure containing components are

properly installed and tightened prior to

pressurizing the system.

4.0 INSTALLATION PREPARATIONS

4.1 Location

For the most accurate flow measurement, a minimum

straight run of pipe is required. Table 1 shows the

minimum straight run requirements. If longer straight

runs are available, position the Verabar such that the

ratio of upstream straight run to downstream straight run

is approximately 4 to 1. If straight run lengths are less

than the values stated in Table 1, consult the factory for

additional accuracy and location information. For

additional piping configurations, see Drawing SUB-4521.

Position straightening vanes such that the end closest to

the Verabar is half way between the Verabar and the

closest upstream configuration. For elbow installations,

mount the Verabar in the same plane as the closest

upstream elbow.

4.2 Orientation

Verify the proper sensor orientation by checking for an

“-H” (horizontal piping) or a “-V” (vertical piping) in the

model number on the Verabar nameplate. Verify the flow

arrow stamped on the instrument head is pointing

downstream in the direction of the flow.

Table 1. Straight Run Requirements

Piping Configuration

1 2 3 4

Résumé du contenu

Page 1 - Verabar V500 and V510

Verabar V500 and V510 INSTALLATION INSTRUCTIONS 1.0 SCOPE These instructions provide procedures for installing the V500 and V510 Verabar flow sens

Page 2

4.2.1 Horizontal Piping For air or gas installations, mount the Verabar in the upper 160° of the pipe to allow any condensate to drain into the pipe

Page 3 - 5.4.2 Manifold

5.2 Weld Mounting Flange to Pipe • Loosely bolt together (hand tight) the sensor, gasket and mounting flange. Insert the assembly into the pipe. A

Page 4 - Printed in USA

The Verabar is now properly installed (Figure 6). Figure 6. Installed V500 and V510

Commentaires sur ces manuels

Pas de commentaire

Veris Verabar V500_V510 Installation Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Veris Verabar V500_V510 Installation Instructions. Veris Verabar V500_V510 Installation Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Veris Verabar V500_V510 Installation Instructions